Hemming Lightweight Fabrics With a Serger & Sewing Machine

We’ll show you the easiest way to make a rolled hem on chiffon fabric, or any other similar lightweight material. We’ll first demonstrate it on the serger, then with a domestic machine for those who don’t own a serger. Using the recommended materials and this technique, the result will be a beautiful rolled hem that looks just as professional as if it came from the store!

A lot of formalwear uses sheer, lightweight fabrics, and this method is a good way to keep the edge looking professional like it had never been modified. Apart from your machine, you’ll only need some small but important materials:

First, you’ll want to choose the right thread. We’ll be using a 100wt poly thread called InvisaFil, which is going to blend really well in the fabric so you don’t even see it. And because the thread is so fine, it will stitch more easily through the thin fabric, resulting in fewer ruffles. It’s important to use a very fine thread like this because apart from showing less, it also won’t weigh down the lightweight fabric either.

Because the thread is so fine, we’re also going to choose a needle with a smaller eye. Choose a size 60/8 or 70/10 microtex needle which works best on light fabrics.

Finally, I’m going to use a bobbin that’s been pre-wound with DecoBob thread. This is an 80wt poly thread that comes already pre-wound on a plastic sided bobbin which will pair well with the top thread. You can alternatively wind your own bobbin with the InvisaFil thread, just remember wind it slowly since the thin thread tends to float away. If you’re going to hem your fabric on a serger, obviously you won’t use a bobbin so you’ll want DecoBob thread on a spool for your lower loopers.

On a Serger: 

We are going to use a 3 thread rolled hem, with InvisaFil in the needle and upper looper, and DecoBob in the lower looper. Consult with your serger manual and adjust the stitch length and cutting blade to get a close narrow hem.

Once your machine is threaded, do a test run on similar fabric to make sure your fabric is not puckering. You may have to adjust your differential settings to get a flat, smooth edge. 

Mark your hem with a disappearing marking pen, and serge exactly along your marked line. This is the simplest method for a quick fine hem on chiffon or similar fine fabric.

On a Domestic Sewing Machine With a Rolled Hem:

If you want to hem fine fabric on a domestic machine, this two step method will help you achieve perfect results. Mark where you want your finished hem and cut 1” below the marked line. We will trim this closer later. Be sure to spread the fabric out flat and even as these types of fabrics can easily shift during cutting. Thread your machine with InvisaFil on top and DecoBob in the bobbin. Now you’re ready to sew!

Using your fingers, tuck the edge of the fabric over 1/8” below the finished hem length and stitch very close to this folded edge. Do this all the way to the end of the fabric. If you’re hemming a sleeve or skirt, or anything where your piece is a loop, we recommend starting and ending on the seam to help hide the backstitching.

When you’re done, use a pair of sharp, fine tipped scissors to cut away the remaining fabric as close as you can to your line of stitching without snipping into the stitching itself. Exercise caution so you don’t accidentally snip over your seam. Do this all the way to the end.

Press all the way around to sink the stitches into the fabric and smooth any puckers.

Once you’ve finished trimming the excess fabric and pressing, tuck the edge 1/8” over one more time (along the finished hem marking) and stitch it down again over the original line of stitching to complete your rolled hem. If you have trouble tucking the edge over with your fingers and keeping the 1/8” length consistent, you can press the edge down with an iron before sewing.

That’s all there is to it! You can see how little the thread shows in the finished hem as well how flat the edge sits because the fine thread doesn’t add extra bulk. As most hems have a curved edge, doing the hem in two steps helps keep your hem even and consistent and eliminates any problems. These materials combined with these simple techniques are all you need for perfect, professional hemming.

(Left: done with serger. Right: done with domestic machine.)

Inspired to sew? Head on over to shopwonderfil.com/shop-local/ for a list of stores and retailers you can purchase WonderFil threads from. You can also sign up to receive weekly sewing tips, free patterns, and tutorials in our newsletter. Register by clicking here! You can unsubscribe at any time by clicking the unsubscribe button on the footer of every email you receive.

The Easiest Way to Hem a Pair of Jeans

Rather than rolling up your jeans or taking them to an expensive tailor, why not hem them yourself? This is one of those life skills that’s easy enough for anyone with a sewing machine to do themselves. Wearing jeans that are too long can wear away the denim around the heel in an ugly way. We’re here to show you our tried and true method of hemming jeans easily and quickly for a perfect fit. We’ll also show you our recommendation for notions that will give you the best look and results.

To begin, you’ll want to grab a piece of tailor’s chalk, preferably in white or another contrasting colour from your denim. Put on the pair of jeans that are too long and turn up the fabric under the wrong side of the pants until it’s at the desired length. We recommend doing this step while wearing shoes to ensure you take this extra height into consideration. It may help to have someone do this for you so you’re standing straight. Make a mark at the base of the fabric at the desired length using the tailor’s chalk.

Now measure the distance from the mark to the bottom of the original hem. You’ll want to mark the other leg at the same distance so they are the same length. Lay one of the legs flat and place a ruler straight against the line. Extend the line all the way down the fabric.

Holding the ruler in place against the line, you can flip over the pant leg over the ruler and continue drawing the line to the other side of the leg, being careful to keep it straight. You should now have a straight line running on both sides of the pant leg.

Do the same with the other pant leg. Now that both legs have been marked, you’ll want to mark your fold lines next. On the side of the line closer to the bottom of the pant leg, measure another half inch and make a new mark.

Now measure another half inch from your new mark, and make a third mark. You’ll want to once again extend these lines straight all the way around the pant leg on both legs. You should now have 3 solid straight lines travelling around both your pant legs.

Using a pair of sharp fabric scissors, cut off the pants closely following the bottom line, the one closest to the bottom of the pant leg. Do this for both pant legs. You can now begin sewing your new hem!

Most denim jeans will have a thick gold coloured thread, so it’s best to choose a thread that matches it to look consistent with the rest of the pants. We’ll be using this 12wt cotton thread called Spagetti in the bobbin. It’s a heavier than your usual 40 or 50wt thread, and closely resembles the decorative contrasting brown or golden thread used on jeans. The two Spagetti colours that tend to match most with this jean thread is SP11 or SP21. For this pair of jeans, I’ll be using colour SP21.

Because we’re using a thicker thread underneath, we want to use a finer thread in the needle. This will ensure the thread doesn’t struggle through the fabric, and it will give you a better stitch consistency and quality. But you don’t want just any finer thread up top, you want to make sure it is strong enough to hold your denim fabric together for a good long time.

We’ll be using DecoBob 80wt thread in the needle. This is a strong but lightweight polyester thread that is ideal to pair with Spagetti in the bobbin. We used a regular 80/12 size needle, however if you find your machine is struggling with the thicker denim fabric, you can also use a denim needle.

Don’t forget to increase your machine’s stitch length to 3.1. This will help with the machine’s tension when using the thicker 12wt thread, and also match the stitch length showing on the jeans.

Once the machine is set up, you can begin sewing. Roll up the hem following the remaining two lines so that the raw edge is tucked away. If you feel confident with keeping it straight you can begin sewing right away. However, we recommend beginners clip their hems in place to prevent it from moving using sewing clips. We prefer sewing clips instead of using pins because the thick denim can be difficult to penetrate with pins, and it doesn’t cause any puckering.

You’ll want to sew on the inside of the pant leg so you can follow the edge of the new hem. This way, your heavy 12wt thread in the bobbin will show on the right side of the pant leg.

We recommend starting on the bump of one of the side seams to hide your backstitching. Because of the thickness of the fabric in this area, you may need to gently turn the handle on the side of your sewing machine to manually sew the first few stitches. Sew close to the edge of the hem, being careful to keep your stitching straight and consistent. When you return to your start point, sew over the original stitching and don’t forget to backstitch again.

Trim your threads and you’re finished! You’ll have a new perfectly fitting pair of jeans that you hemmed yourself.

Inspired to sew? Head on over to shopwonderfil.com/shop-local/ for a list of stores and retailers you can purchase WonderFil threads from. You can also sign up to receive weekly sewing tips, free patterns, and tutorials in our newsletter. Register by clicking here! You can unsubscribe at any time by clicking the unsubscribe button on the footer of every email you receive.